Minicom Advanced Systems Smart 4 Guía de usuario Pagina 84
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operating the SmartRack 116 IP S
witching System Locally
Troubleshooting – Update Software
84 | SmartRack 116 IP
5. Click Start.
The SmartRack 116 IP
Switch Update flashes the firmware. On completion
firmware version number appears.
If the status of the device is busy
cannot be upgraded. To free the device
device resets
and the status is now free. Click
6.
Check that the updated version number is correct by pressing
Manually Updating the
RICC/ROCs
You can manually update the RICC/ROCs after starting the Update software.
To manually update the
RICC/ROCs
1.
Select one or more ROCs..
2. Press Options -
> Advanced
3.
Open the appropriate hex fi
4. Click Start.
The firmware updates.
6.3.9
Restoring Factory Settings
You can restore the OSD to the factory settings from the Update software.
All changes made (
such as
removed.
To restore the OSD factory settings:
1. Select
Options/Advanced/Set default
The OSD returns to the factory default settings.
You can also restore the OSD
6.4
Troubleshooting
This section
describes how to troubleshoot the following problems that may arise
when updating the
SmartRack 116 IP
Unit hangs or mouse malfunctions
Break in communication
witching System Locally
Switch Update flashes the firmware. On completion
firmware version number appears.
If the status of the device is busy
- see the bottom of Figure 83-
the system
cannot be upgraded. To free the device
, choose
Options/Advanced/Reset
and the status is now free. Click
Start.
Check that the updated version number is correct by pressing
RICC/ROCs
You can manually update the RICC/ROCs after starting the Update software.
RICC/ROCs
:
Select one or more ROCs..
> Advanced
-> Manual Update.
Open the appropriate hex fi
le.
Restoring Factory Settings
You can restore the OSD to the factory settings from the Update software.
such as
passwords, access rights, and
names) will be
To restore the OSD factory settings:
Options/Advanced/Set default
.
The OSD returns to the factory default settings.
You can also restore the OSD
default settings from the OSD (F7) (
see
Troubleshooting
– Update Software
describes how to troubleshoot the following problems that may arise
SmartRack 116 IP
firmware:
Unit hangs or mouse malfunctions
Switch Update flashes the firmware. On completion
, the
the system
Options/Advanced/Reset
. The
.
You can manually update the RICC/ROCs after starting the Update software.
You can restore the OSD to the factory settings from the Update software.
names) will be
see
page 71)
describes how to troubleshoot the following problems that may arise
- SmartRack 116 IP 1
- User Guide 1
- Legal Notice 2
- About this Document 3
- Style Conventions 4
- Table of Contents 5
- User Guide 7
- Table of Figures 10
- User Guide 11
- 1 Introduction 12
- 1.2 Terminology 13
- 1.3 Compatibility 13
- 1.5 Technical Precautions 13
- 1.7 Trademarks 14
- 1.8 WEEE Compliance 14
- 1.6 Safety 14
- 2 Installation 15
- Installation 16
- System Components 16
- 16 16
- The SmartRack 116 IP Unit 17
- Pre-Installation Guidelines 18
- 18 18
- Replacing the Bracket 19
- Connecting 20
- User Guide 21
- 22 22
- 2.5 Connecting the System 23
- 2.6 Connecting to the Servers 23
- Connecting a RICC/ROC PS/2 24
- Connecting a RICC 25
- /ROC USB 25
- Connecting a RICC SUN 26
- User Guide 27
- 3 Configuring the Network 28
- Interface 29
- Configuring the Network 30
- 30 30
- User Guide 31
- 32 32
- 3.3.2 Configuring 33
- Adding a User 34
- Configuring User Settings 35
- User Guide 35
- Deleting User(s) 36
- Blocking a User 36
- Editing User 36
- Information 36
- Configuring the KVM Switch 37
- 38 38
- Installing 40
- Upgrading Firmware 40
- User Guide 41
- 3.9 Reloading a 42
- 44 44
- Conducting 45
- Conducting a Remote Session 46
- Starting a Remote Session 46
- 46 46
- 4.2 Sharing a Remote Session 47
- Exclusive 48
- Full Screen Mode 49
- Verifying 50
- 50 50
- Adjusting the Video 52
- Manually 53
- Adjusting Video Settings 53
- Managing Keyboard Sequences 54
- User Guide 55
- Recording a New Custom Key 56
- Editing a Key Sequence 56
- Synchronizing Mouse Pointers 57
- 58 58
- The USB Option 59
- Aligning the M 60
- Pointers 60
- Calibrating Mouse 61
- 5 Troubleshooting – Safe Mode 62
- Restoring Factory Defaults 63
- Restoring the Device Firmware 64
- Figure 73 – Upgrade Succeeded 65
- Operating 66
- Using the Keyboard Hotkeys 66
- 66 66
- 6.2.3 Configuring t 67
- Configuring Security Settings 69
- Operating the SmartR 70
- Using the OSD 70
- 70 70
- Configuring the Port 71
- Configuring the T 72
- Configuring the Users 73
- Settings 73
- 74 74
- OSD Functions 75
- Scanning 76
- Computers (F4) 76
- Tuning (F5) 76
- Moving the Label ( F6) 77
- 78 78
- Starting and C 80
- Software 80
- Verifying the V 81
- RICC/ROC Version 82
- Obtaining N 83
- Firmware 83
- Troubleshooting 84
- – Update Software 84
- 6.4.4 Electricity F 85
- 86 86
- 7 Technical Specifications 87
- Technical Specifications 88
- 88 88
- User Guide 89
- 9 SNMP Events Table 90
- SNMP Events Table 91
- User Guide 91
- 201204210 • 933213_EN 92
Relacionado con productos y manuales para Redes Minicom Advanced Systems Smart 4
(92 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales