Minicom Advanced Systems Smart 4 Guía de usuario Pagina 67
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Lines with yellow text show active computers. Lines with blue text show inactive
computers. The Type
column indic
is connected to the port.
6.2.1
Navigating the OSD
You can navigate the OSD, as follows:
To move up and down
To jump from one column to the next (when relevant)
To exit the OSD or return to a previous window within the OSD
6.2.2
Selecting a Computer
To select a computer:
1.
Navigate to the desired computer line.
OR
Type the port number of the desired computer.
2. Press Enter.
The selected computer is accessed. A Confirmation label appears showing which
computer is accessed
.
When the OSD is displayed
Select buttons or the
6.2.3 Configuring t
he OSD Settings
You can configure the following OSD settings:
General (see Section
6.2.4
Operating
the SmartRack 116 IP Switching System Locally
Figure 74 – OSD Main Window
Lines with yellow text show active computers. Lines with blue text show inactive
column indic
ates that a computer “C”
or another switch “S”
is connected to the port.
Navigating the OSD
You can navigate the OSD, as follows:
To move up and down
– Use the Up and Down arrow keys.
To jump from one column to the next (when relevant)
– Use the
Tab
To exit the OSD or return to a previous window within the OSD
– P
ress
Selecting a Computer
Navigate to the desired computer line.
Type the port number of the desired computer.
The selected computer is accessed. A Confirmation label appears showing which
.
When the OSD is displayed
,
you cannot select computers using
Select buttons or the
keyboard hotkeys.
he OSD Settings
You can configure the following OSD settings:
6.2.4
)
the SmartRack 116 IP Switching System Locally
Using the OSD
User Guide | 67
Lines with yellow text show active computers. Lines with blue text show inactive
or another switch “S”
Tab
key.
ress
Esc.
The selected computer is accessed. A Confirmation label appears showing which
you cannot select computers using
the front panel
- SmartRack 116 IP 1
- User Guide 1
- Legal Notice 2
- About this Document 3
- Style Conventions 4
- Table of Contents 5
- User Guide 7
- Table of Figures 10
- User Guide 11
- 1 Introduction 12
- 1.2 Terminology 13
- 1.3 Compatibility 13
- 1.5 Technical Precautions 13
- 1.7 Trademarks 14
- 1.8 WEEE Compliance 14
- 1.6 Safety 14
- 2 Installation 15
- Installation 16
- System Components 16
- 16 16
- The SmartRack 116 IP Unit 17
- Pre-Installation Guidelines 18
- 18 18
- Replacing the Bracket 19
- Connecting 20
- User Guide 21
- 22 22
- 2.5 Connecting the System 23
- 2.6 Connecting to the Servers 23
- Connecting a RICC/ROC PS/2 24
- Connecting a RICC 25
- /ROC USB 25
- Connecting a RICC SUN 26
- User Guide 27
- 3 Configuring the Network 28
- Interface 29
- Configuring the Network 30
- 30 30
- User Guide 31
- 32 32
- 3.3.2 Configuring 33
- Adding a User 34
- Configuring User Settings 35
- User Guide 35
- Deleting User(s) 36
- Blocking a User 36
- Editing User 36
- Information 36
- Configuring the KVM Switch 37
- 38 38
- Installing 40
- Upgrading Firmware 40
- User Guide 41
- 3.9 Reloading a 42
- 44 44
- Conducting 45
- Conducting a Remote Session 46
- Starting a Remote Session 46
- 46 46
- 4.2 Sharing a Remote Session 47
- Exclusive 48
- Full Screen Mode 49
- Verifying 50
- 50 50
- Adjusting the Video 52
- Manually 53
- Adjusting Video Settings 53
- Managing Keyboard Sequences 54
- User Guide 55
- Recording a New Custom Key 56
- Editing a Key Sequence 56
- Synchronizing Mouse Pointers 57
- 58 58
- The USB Option 59
- Aligning the M 60
- Pointers 60
- Calibrating Mouse 61
- 5 Troubleshooting – Safe Mode 62
- Restoring Factory Defaults 63
- Restoring the Device Firmware 64
- Figure 73 – Upgrade Succeeded 65
- Operating 66
- Using the Keyboard Hotkeys 66
- 66 66
- 6.2.3 Configuring t 67
- Configuring Security Settings 69
- Operating the SmartR 70
- Using the OSD 70
- 70 70
- Configuring the Port 71
- Configuring the T 72
- Configuring the Users 73
- Settings 73
- 74 74
- OSD Functions 75
- Scanning 76
- Computers (F4) 76
- Tuning (F5) 76
- Moving the Label ( F6) 77
- 78 78
- Starting and C 80
- Software 80
- Verifying the V 81
- RICC/ROC Version 82
- Obtaining N 83
- Firmware 83
- Troubleshooting 84
- – Update Software 84
- 6.4.4 Electricity F 85
- 86 86
- 7 Technical Specifications 87
- Technical Specifications 88
- 88 88
- User Guide 89
- 9 SNMP Events Table 90
- SNMP Events Table 91
- User Guide 91
- 201204210 • 933213_EN 92
Relacionado con productos y manuales para Redes Minicom Advanced Systems Smart 4
(92 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales