Minicom Advanced Systems Smart 4 Guía de usuario Pagina 34
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring the Network
Configuring Network SNMP Settings
34 | SmartRack 116 IP
In Manager IP Address
, type the static IP address of the Centralized Management
Manager.
Although not required, it is
if the
SmartRack 116 IP
Centralized Management Manager
3.4
Configuring Network SNMP Settings
You can activate SNMP logging
the SmartRack 116 IP
to send monitoring events (such as log entries) to the SNMP
server. See Chapter 9
for a list of all recorded SNMP events.
To enable and configure
SNMP
1.
From the configuration men
The SNMP page opens.
2. Select the Enable Traps
checkbox t
and operation.
3. In Community, type the
name of the
4. In SNMP Manager IP,
type the SNMP Server IP address.
3.5
Configuring User Settings
An Administrator can
add, edit, remove
There are two levels of user access:
Administrator –
has unrestricted access to all windows and settings, and can
change the name and password of all users
User – can access and
control
settings and power cycle
; cannot access the
3.5.1 Adding a User
To add a User:
1.
From the configuration menu, select
, type the static IP address of the Centralized Management
Although not required, it is
recommended to type the
Manager IP Address
SmartRack 116 IP
resides on the same network segment
as the
Centralized Management Manager
.
Configuring Network SNMP Settings
You can activate SNMP logging
to provide support network monitoring. This will cause
to send monitoring events (such as log entries) to the SNMP
for a list of all recorded SNMP events.
SNMP
logging:
From the configuration men
u, select SNMP.
Figure 37 – SNMP Settings
checkbox t
o enable SNMP traps of
SmartRack 116 IP
name of the
SNMP community.
type the SNMP Server IP address.
Configuring User Settings
add, edit, remove
, and block Users.
There are two levels of user access:
has unrestricted access to all windows and settings, and can
change the name and password of all users
control
target s
ervers, but cannot use advanced mouse
; cannot access the
Web configuration interface
From the configuration menu, select
Users.
, type the static IP address of the Centralized Management
Manager IP Address
even
as the
to provide support network monitoring. This will cause
to send monitoring events (such as log entries) to the SNMP
SmartRack 116 IP
events
has unrestricted access to all windows and settings, and can
ervers, but cannot use advanced mouse
Web configuration interface
- SmartRack 116 IP 1
- User Guide 1
- Legal Notice 2
- About this Document 3
- Style Conventions 4
- Table of Contents 5
- User Guide 7
- Table of Figures 10
- User Guide 11
- 1 Introduction 12
- 1.2 Terminology 13
- 1.3 Compatibility 13
- 1.5 Technical Precautions 13
- 1.7 Trademarks 14
- 1.8 WEEE Compliance 14
- 1.6 Safety 14
- 2 Installation 15
- Installation 16
- System Components 16
- 16 16
- The SmartRack 116 IP Unit 17
- Pre-Installation Guidelines 18
- 18 18
- Replacing the Bracket 19
- Connecting 20
- User Guide 21
- 22 22
- 2.5 Connecting the System 23
- 2.6 Connecting to the Servers 23
- Connecting a RICC/ROC PS/2 24
- Connecting a RICC 25
- /ROC USB 25
- Connecting a RICC SUN 26
- User Guide 27
- 3 Configuring the Network 28
- Interface 29
- Configuring the Network 30
- 30 30
- User Guide 31
- 32 32
- 3.3.2 Configuring 33
- Adding a User 34
- Configuring User Settings 35
- User Guide 35
- Deleting User(s) 36
- Blocking a User 36
- Editing User 36
- Information 36
- Configuring the KVM Switch 37
- 38 38
- Installing 40
- Upgrading Firmware 40
- User Guide 41
- 3.9 Reloading a 42
- 44 44
- Conducting 45
- Conducting a Remote Session 46
- Starting a Remote Session 46
- 46 46
- 4.2 Sharing a Remote Session 47
- Exclusive 48
- Full Screen Mode 49
- Verifying 50
- 50 50
- Adjusting the Video 52
- Manually 53
- Adjusting Video Settings 53
- Managing Keyboard Sequences 54
- User Guide 55
- Recording a New Custom Key 56
- Editing a Key Sequence 56
- Synchronizing Mouse Pointers 57
- 58 58
- The USB Option 59
- Aligning the M 60
- Pointers 60
- Calibrating Mouse 61
- 5 Troubleshooting – Safe Mode 62
- Restoring Factory Defaults 63
- Restoring the Device Firmware 64
- Figure 73 – Upgrade Succeeded 65
- Operating 66
- Using the Keyboard Hotkeys 66
- 66 66
- 6.2.3 Configuring t 67
- Configuring Security Settings 69
- Operating the SmartR 70
- Using the OSD 70
- 70 70
- Configuring the Port 71
- Configuring the T 72
- Configuring the Users 73
- Settings 73
- 74 74
- OSD Functions 75
- Scanning 76
- Computers (F4) 76
- Tuning (F5) 76
- Moving the Label ( F6) 77
- 78 78
- Starting and C 80
- Software 80
- Verifying the V 81
- RICC/ROC Version 82
- Obtaining N 83
- Firmware 83
- Troubleshooting 84
- – Update Software 84
- 6.4.4 Electricity F 85
- 86 86
- 7 Technical Specifications 87
- Technical Specifications 88
- 88 88
- User Guide 89
- 9 SNMP Events Table 90
- SNMP Events Table 91
- User Guide 91
- 201204210 • 933213_EN 92
Relacionado con productos y manuales para Redes Minicom Advanced Systems Smart 4
(92 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales